IGS-6325-4UP2X di Planet Technology: Switch Industriale L3 con PoE++ 360W e Connettività 2.5G/10G
Il modello IGS-6325-4UP2X di Planet Technology è uno switch industriale managed di livello L3, caratterizzato da 4 porte 2.5Gb Base T e 2 porte 10Gb SFP PoE con un budget PoE di 360W, progettato per applicazioni che richiedono alte prestazioni, versatilità e affidabilità. Adatto per ambienti estremi, offre una solida base per reti industriali avanzate.
Caratteristiche Principali:
| Specifiche Tecniche | |
|---|---|
| Copper Ports | 4 2.5GBASE-T RJ45 auto negotiation port Supports 2.5G/1G/100/10Mbps data rate |
| SFP+ Ports | 2 10GBASE-SR/LR SFP+ slots Backward compatible with 1000BASE-SX/LX/BX and 2500BASE-X SFP transceivers |
| PoE Injector Ports | 4 ports with 802.3bt PoE++ injector function, from Port-1 to Port-4 |
| Console | 1 x RJ45-to-RS232 serial port (115200, 8, N, 1) |
| Reset Button | < 5 sec: System reboot > 5 sec: Factory default |
| Connector | Removable 6-pin terminal block for power input Pin 1/2 for Power 1, Pin 3/4 for Alarm, Pin 5/6 for Power 2 Removable 6-pin terminal block for DI/DO interface Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND |
| Alarm | One relay output for power failure. Alarm relay current carry ability: 1A @ 24VDC |
| Digital Input (DI) | 2 digital inputs: Level 0: -24~2.1V (±0.1V) Level 1: 2.1~24V (±0.1V) Input load to 24VDC, 10mA max. |
| Digital Output (DO) | 2 digital outputs: Open collector to 24VDC, 100mA |
| Enclosure | IP30 aluminum case |
| Installation | DIN-rail or wall-mount |
| SDRAM | 512Mbytes |
| Flash Memory | 64Mbytes |
| Dimensions (W x D x H) | 76 x 135 x 152 mm |
| Weight | 1,319g |
| Power Requirements | DC 48V-54V, 8.3A max. |
| Power Consumption | 48VDC Input: Max. 8.9 watts/30.4 BTU (Idle) Max. 379 watts/1293.2 BTU (Full load) 54VDC Input: Max. 9.2 watts/31.4 BTU (Idle) Max. 381 watts/1300 BTU (Full load) |
| ESD Protection | Contact 4KVDC; Air 8KVDC |
| Surge Protection | 2KVDC |
| LED Indicators | System: Power 1 (Green), Power 2 (Green) Alarm (Red) Ring (Green), Ring Owner (Green) DI/DO (Red) PoE Usage: 120W/240W/360W (Amber) Per 10/100/1G/2.5GBASE-T RJ45 Port: Data LED: 1G/2.5G LNK/ACT (Green) 10/100 LNK/ACT (Amber) PoE LED: IEEE 802.3bt Mode (Green) IEEE 802.3at Mode (Amber) Per 1G/2.5G/10GBASE-X SFP+ Port: 1G/2.5Gbps LNK/ACT (Green) 10Gbps LNK/ACT (Amber) |
| Switching Specifications | |
| Switch Architecture | Store-and-Forward |
| Switch Fabric | 60Gbps/non-blocking |
| Throughput | 44.462Mpps@64Bytes |
| Address Table | 8K entries, automatic source address learning and aging |
| Shared Data Buffer | 32Mbits |
| Jumbo Frame | 10K bytes |
| Flow Control | IEEE 802.3x pause frame for full duplex Back pressure for half duplex |
| Power over Ethernet | |
| PoE Standard | IEEE 802.3bt PoE++ Type-4 |
| PoE Power Supply Type | End-span Mid-span BT |
| Power Pin Assignment | 802.3bt/UPoE: 1/2(-), 3/6(+), 4/5(+), 7/8(-) 802.3at/PoE: End-span: 1/2(-), 3/6(+) 802.3at/PoE: Mid-span: 4/5(+), 7/8(-) |
| PoE Power Output | Per port 48V ~ 54VDC -802.3bt Type-4 mode: maximum 95 watts -End-span mode: maximum 36 watts -Mid-span mode: maximum 36 watts -Force mode: maximum 95 watts |
| PoE Power Budget | Single power input: 240W maximum (depending on power input) Dual power input: 360W maximum (depending on power input) ※Dual power input must be the same as DC voltage, like dual 54V. |
| Number of 90W 802.3bt Type-4 PDs | 4 |
| Number of 60W 802.3bt Type-3 PDs | 4 |
| Number of 30W 802.3at Type-2 PDs | 4 |
| PoE Management Functions | |
| Enhanced PoE Mode | Standard/Legacy/Force |
| PoE Management | PD Alive Check Scheduled Power Recycling PoE Schedule PoE Usage Monitoring PoE Extension |
| Active PoE Device Live Detection | Yes |
| PoE Power Recycling | Yes, daily or predefined schedule |
| PoE Schedule | 4 schedule profiles |
| PoE Extend Mode | Yes, max. up to 160 meters |
| Layer 3 Functions | |
| IP Interfaces | Max. 32 VLAN interfaces |
| Routing Table | Max. 32 static routing entries Max. 1K routing table entries |
| Routing Protocols | IPv4 RIPv2 IPv4 OSPFv2 IPv6 OSPFv3 IPv4 hardware static routing IPv6 hardware static routing |
| Layer 2 Functions | |
| Port Configuration | Port disable/enable Auto-negotiation 10/100/1000/2500Mbps full and half duplex mode selection Flow control disable/enable Port link capability control |
| Port Status | Display of each port’s speed duplex mode, link status, flow control status, auto-negotiation status and trunk status |
| Port Mirroring | TX/RX/Both Many-to-1 monitor RMirror – Remote Switched Port Analyzer (Cisco RSPAN) Supports up to 5 sessions |
| VLAN | IEEE 802.1Q tagged VLAN IEEE 802.1ad Q-in-Q tunneling Private VLAN Edge (PVE) MAC-based VLAN Protocol-based VLAN Voice VLAN IP Subnet-based VLAN MVR (Multicast VLAN registration) GVRP Up to 4K VLAN groups, out of 4095 VLAN IDs |
| Link Aggregation | IEEE 802.3ad LACP/static trunk Max. 3 trunk groups with max. 6 ports per trunk group |
| Spanning Tree Protocol | IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol Supports 7 MSTP instances BPDU Guard, BPDU filtering and BPDU transparent Root Guard |
| IGMP Snooping | IPv4 IGMP (v1/v2/v3) snooping IPv4 IGMP querier mode support Supports 255 IGMP groups |
| MLD Snooping | IPv6 MLD (v1/v2) snooping, IPv6 MLD querier mode support Supports 255 MLD groups |
| Bandwidth Control | Per port bandwidth control Ingress: 10Kbps~13128Mbps Egress: 10Kbps~13128Mbps |
| Ring | Supports ERPS, and complies with ITU-T G.8032 Recovery time < 10ms @ 3 nodes Recovery time < 50ms @ 16 nodes Supports Major ring and sub-ring |
| Synchronization | IEEE 1588v2 PTP (Precision Time Protocol) Peer-to-peer transparent clock End-to-end transparent clock |
| QoS | Traffic classification based, strict priority and WRR 8-level priority for switching: Port number 802.1p priority 802.1Q VLAN tag DSCP/ToS field in IP packet |
| Security Functions | |
| Access Control List | IP-based ACL/MAC-based ACL ACL based on: |
Please sign in first.
Sign in
