Industrial L3 8-Porte 10/100/1000T 802.3Bt Poe + 2-Porte 1G/2.5G Sfp + 4-Porte 10G Sfp+ Managed Ethernet Switch

Riferimento:IGS63298UP2S4X

Industrial Layer 3 5-Porte 10Gbase-X Sfp+ + 1-Porte 10Gbase-T Managed Ethernet Switch

Layer 3 8-Porte 10Gbase-X Sfp+ + 8-Porte 10Gbase-T Managed Ethernet Switch

Descrizione

Descrizione

IGS63298UP2S4X Industrial L3 8-Porte 10/100/1000T 802.3bt PoE + 2-Porte 1G/2.5G SFP + 4-Porte 10G SFP+ Managed Ethernet Switch

Specifiche Tecniche
Copper Ports	8 10/100/1000BASE-T RJ45 auto-MDI/MDI-X ports
SFP Ports	2 1000BASE-SX/LX/BX SFP slot interfaces (Port-9 and Port-10) Compatible with 100BASE-FX and 2500BASE-X SFP
SFP+ Ports	4 10GBASE-SR/LR SFP+ slot interfaces (Port-11 to Port-14) Compatible with 1000BASE-X and 2500BASE-X SFP
PoE Injector Ports	8 ports with 802.3bt PoE++ injector function with Port-1 to Port-8
Console	1 x RJ45-to-RS232 serial port (115200, 8, N, 1)
Reset Button	< 5 sec: System reboot > 5 sec: Factory default
Connector	Removable 6-pin terminal block for power input 　Pin 1/2 for Power 1, Pin 3/4 for fault alarm, Pin 5/6 for Power 2 Removable 6-pin terminal block for DI/DO interface 　Pin 1/2 for DI 1 & 2, Pin 3/4 for DO 1 & 2, Pin 5/6 for GND
Alarm	One relay output for power failure. Alarm relay current carry ability: 1A @ 24V DC
Digital Input (DI)	2 digital inputs: 　Level 0: -24~2.1V (±0.1V) 　Level 1: 2.1~24V (±0.1V) 　Input load to 24V DC, 10mA max.
Digital Output (DO)	2 digital outputs: 　Open collector to 24VDC, 100mA
Enclosure	IP30 aluminum case
Installation	DIN-rail or wall mounting
Dimensions (W x D x H)	76 x 135 x 152 mm
Weight	1,619g
Power Requirements	Dual DC 48~54V, 8A max. (>52V DC for 802.3bt PoE++ output recommended)
Power Consumption	Max. 12.4 watts/42.3BTU@54V DC input (System on) Max. 430 watts/1467.2BTU@54V DC input (Full loading with 802.3bt PoE++ function)
ESD Protection	Air 8KV DC Contact 6KV DC
Surge Protection	4KV DC
LED Indicator	System: 　Power 1 (Green), Power 2 (Green), Alarm (Red) 　Ring (Green), Ring Owner (Green), DIDO (Red) Per 10/100/1000T RJ45 PoE++ Port: 　1000Mbps LNK/ACT (Green) 　10/100Mbps LNK/ACT (Amber) 　802.3bt PoE++-in-use x 1 (Green) 　802.3at/af PoE-in-use x 1 (Amber) Per SFP Interface: 　1G/2.5G LNK/ACT (Green) 　100 LNK/ACT (Amber) Per SFP+ Port: 　10Gbps LNK/ACT (Green) 　1Gbps LNK/ACT (Amber) PoE Usage: 　90W, 180W, 270W, 360W (Amber)
Switching Specifications
Switch Architecture	Store-and-Forward
Switch Fabric	106Gbps/non-blocking
Throughput (packet per second)	78.87Mpps@ 64 bytes packet
Address Table	32K entries, automatic source address learning and aging
Shared Data Buffer	32Mbits
Jumbo Frame	10Kbytes
SDRAM	512Mbytes
Flash Memory	64Mbytes
Flow Control	IEEE 802.3x pause frame for full-duplex Back pressure for half-duplex
Power Over Ethernet
PoE Standard	IEEE 802.3bt PoE++ Type-4 PSE Backward compatible with 802.3at PoE+ PSE
PoE Power Supply Type	802.3bt UPOE/POH End-span Mid-span Force
PoE Power Output	802.3bt PoE++ 　Per port 52V~54V DC (depending on the power supply), max. 90 watts UPoE(PoH) 　Per port 52V~54V DC (depending on the power supply), max. 95 watts IEEE 802.3at Standard 　Per port 52V~54V DC (depending on the power supply), max. 36 watts Force 　Per port 52V~54V DC (depending on the power supply), max. 60 watts
Power Pin Assignment	End-span: 1/2(-), 3/6(+) Mid-span: 4/5(+), 7/8(-) 802.3bt/UPoE: 1/2(-), 3/6(+),4/5(+), 7/8(-)
PoE Power Budget	Single power input: 240W maximum (depending on power input) 　Dual power input: 360W maximum (depending on power input) ※Dual power input must be the same as DC voltage, like dual 54V
PoE Ability PD @ 12.5 watts	8 units
PoE Ability PD @ 25 watts	8 units
PoE Ability PD @ 51 watts	6 units
PoE Ability PD @ 71 watts	4 units
PoE Management Functions
Active PoE device alive detects	Yes
PoE Power Recycle	Yes, daily or predeinded schedule
PoE Schedule	4 schedule profiles
PoE Extend Mode	Yes, max. 160 to 200 meters
PoE System Management	System PoE Admin control Total PoE power budget control Auto power input and PoE budget control PoE Legacy mode Over-temperature threshold alarm PoE usage threshold alarm
PoE Port Management	Port Enable/Disable/Schedule PoE mode control 　802.3bt 　UPoE 　802.3at End-span 　802.3at Mid-span Force mode Port Priority
Layer 2 Functions
Port Configuration	Port disable/enable Auto-negotiation 10/100/1000Mbps full and half duplex mode selection Flow control disable/enable Port link capability control
Port Status	Display each port’s speed duplex mode, link status, flow control status, auto negotiation status, trunk status
Port Mirroring	TX/RX/both Many-to-1 monitor Supports up to 5 sessions
VLAN	IEEE 802.1Q tagged VLAN IEEE 802.1ad Q-in-Q tunneling Private VLAN Edge (PVE) MAC-based VLAN Protocol-based VLAN Voice VLAN MVR (Multicast VLAN Registration) GVRP Up to 4K VLAN groups, out of 4095 VLAN IDs
Link Aggregation	IEEE 802.3ad LACP/static trunk Supports 3 trunk groups with 4 ports per trunk group
Spanning Tree Protocol	IEEE 802.1D Spanning Tree Protocol IEEE 802.1w Rapid Spanning Tree Protocol IEEE 802.1s Multiple Spanning Tree Protocol
IGMP Snooping	IPv4 IGMP (v1/v2/v3) snooping IPv4 IGMP querier mode support Supports 255 IGMP groups
MLD Snooping	IPv6 MLD (v1/v2) snooping, IPv6 MLD querier mode support Supports 255 MLD groups
Bandwidth Control	Per port bandwidth control 　Ingress: 500Kb~1000Mbps 　Egress: 500Kb~1000Mbps
Ring	Supports ERPS, and complies with ITU-T G.8032 Recovery time < 10ms Supports Major ring and sub-ring
Synchronization	IEEE 1588v2 PTP(Precision Time Protocol) 　Peer-to-peer transparent clock 　End-to-end transparent clock
QoS	Traffic classification based, strict priority and WRR 8-level priority for switching 　Port number 　802.1p priority 　802.1Q VLAN tag 　DSCP/TOS field in IP packet
Layer 3 Functions
IP Interfaces	Max. 128 VLAN interfaces
Routing Table	Max. 128 routing entries
Routing Protocols	IPv4 hardware static routing IPv6 hardware static routing RIPv2 dynamic routing IPv4 OSPFv2 dynamic routing IPv6 OSPFv3 dynamic routing